Angelia 7500
3-Step Pressure Extraction Doubles the squeeze!

Name of Parts & Accessories

1. Reverse Button 2. Stop(OFF) Button 3. Start Button 4. Clamps 5. Motor Shaft (for Driving Gear) 6. Power Lamp 7. Twin Gears 8. Sub-Shaft (for Free Wheel Gear) 9. Gear Shaft 10. Feeding Chute 11. Grinding Screen 12. Triturating Screen 13. Power Cord Connector 14. Main (Power) Switch 15. Fuse Holder (Box) 16. Screen Housing Cover 17. Wooden Pusher 18. Cleaning Brush 19. Screen Cleaning Knife 20. Power Cord 21. Juice Tub 22. Pulp Collector

How to Operate

1. Please wash the parts thoroughly by rinsing with lukewarm water before first use of your Super Angel Juice Extractor. This will eliminate any traces of dust or residue from manufacturing or shipping.

2. Plug the power cord into the electrical outlet on the wall.

3. Connect the other side of the power cord into the power cord connector of the motor base unit.

4. Place the juice tub under the screen housing.

5. Place the pulp collector under the pulp outlet.

6. Push the main power switch ON (Red Rocker Switch).

7. Check the power indicator(red light) is ON. Now, ready to juice!

8. Start juicing by pressing the 'Start'button.

9. Insert the small amount of Vegetable into the feeding chute by pressing with the wooden pusher.

Note: When operating the juice extractor, please do not let the twin gears idle without food in the feeding chute for extended periods of time. Running the gears excessively while no food is inputted may cause irregular operation. It is suggested to turn the switch on or off depending on when actual juicing is done.

How to Disassemble

Make sure to unplug the power cord from the electrical outlet before starting disassembly. Place the clean, soft towel underneath the screen housing for preventing the damage of parts when dropped. Before start the following steps, let the machine run for about one minute to get rid of excess feed/juice. Remove the Screen Housing Cover.Then, follow the instruction below.

1. Unplug the power cord from the power cord connector on the rear side of the motor base unit.

2. Lift the Clamp up to release.

3. Hold the motor base unit by one hand and pull the Screen Housing out by the other hand.
*When the screen housing is not released smoothly.

1. Plug the power cord into the electrical outlet.
2. Turn the main (red rocker) switch ON.
3. Press START button and then, slowly pull the screen housing out with careful attention.
   The twin gears will be stopped automatically.
4. Turn the main(red rocker) switch OFF.
5. Unplug the power cord from the electrical outlet.

4. Carefully pull the Twin Gears out by holding with both hands.

5. Remove fibers lodging on the screen area by using the Screen Cleaning Knife.

6. Clean the Screen Housing & Twin Gears with the Cleaning Brush under the running water. *Tips for cleaning the Screen Housing? Slowly insert the Cleaning Brush into the Screen Housing and  then pull the Cleaning Brush out by turning clockwise continuously. Repeat this step 4 or 5 times.

7. For keeping the best polish, clean the parts with the soft sponge first and dry it with the soft towel.

How to Assemble

Make sure to unplug the power cord from the electrical outlet before starting assembly. Place the clean, soft towel underneath the screen housing for preventing the damage of parts when dropped. Then, follow the instruction below.

1. First, Insert the Driving Gear through the Driving Gear Shaft. Then, push the gear fully into the slot. Make sure the gears are fully seated.

2. Second, Insert the Free Wheel Gear through the Sub-Shaft.

3. Always make sure the gears are fully seated before operating.If you forcefully push the gear all the way into the slot without properly aligning them, the gear shaft can get damaged.

4. Slowly slide the screen housing over the twin gears and push it back.

5. Push the clamp down to lock the screen housing to the motor base unit.

6. Place the screen housing cover on the screen housing.

Juicing Tips
Tips to maximize effective juicing with your Super Angel Juicer?

The Super Angel Juicer's twin gears are designed to operate at a slow RPM in order to keep almost 100% of the enzymes and nutrients alive during the juicing process. The Super Angel Juicer is the only juicer on the market that limits twin gear speeds to 82 RPM. Accordingly, to maintain the juicer's effectiveness you should not overload the feeding chute. Doing so may cause the gears to jam and limit maximum enzyme and nutrient extraction.

Juicing Tip

1. Completely depress food into the feeding chute with the wooden pusher and then feed addi- di tional food: Don't worry about depressing the wooden pusher till it touches the twin
   It will not harm the gears or plunger. The plunger is made from the same high quality wood as those found in fine chopping blocks. Any accidental particles of cellulose scrapped off from contact with the twin gears are natural and non-toxic and will harmlessly pass through with the pulp.
2. If jamming occurs: press and hold the‘Reverse’Button for 2 to 3 seconds (or press and hold down as required until it clears) and then press the‘Start’Button to continue juicing.
   Depending on the severity of the jam, you may need to repeat this process 2 or more times.
3. Do not apply the excessive force(pressure) while pushing food down into the feeding chute. The moderate pressure is required to avoid jamming or getting stuck.

Helpful Hints for juicing

Carrots: Cutting carrots aren't necessary as long as the diameters fit into the feeding chute. However for best results, we suggest you cut the carrots lengthwise into 5 to 6 inches parts and always insert the thinner part first as it would be grabbed more effectively by the twin gears. Please insert a piece after one piece crushed down completely. Do not put a number of small chopped pieces of carrots at a time into the feeding chute, otherwise it will get stuck.

* Do not apply the excessive force(pressure) while pushing food down into the feeding chute. The moderate pressure is required to avoid jamming or getting stuck.

Dandelion, Parsley, Endive or other leafy greens: By feeding small, handful amounts at a time, the leafy greens will be self-fed into the juicer by the twin gears. Please insert the stem (stalk) part of the leafy greens first for self-feeding.

Wheatgrass: Feed small, handful amounts of wheatgrass into the feeding chute. The wooden pusher may not be necessary as the wheatgrass will be self-fed into the machine as long as appropriate amounts are fed at a time. Do not overload.

How to Clean

In order to extend the life span of juice extractor, you need to clean all parts immediately after use, before mineral build-up which can cause problems.

1. Completely disassemble the screen housing and twin gears.
2. Remove fibers lodging on the screen area by using the screen cleaning knife.
   (Fig. #5)
3. Clean the screen housing & twin gears with the cleaning brush under the running water. Tips for Cleaning the Screen Housing : Carefully insert the cleaning brush into the screen housing and then pull the cleaning brush out by slowly turning clockwise continuously. Repeat this step 4 or 5 times. (Fig. #6)
4. For keeping the best polish, clean the parts with the soft sponge first and dry it with the soft towel. After cleaning the juice extractor, let it dry thoroughly.

Tip for Cleaning

Maintaining maximum cleanliness of your juicer is extremely important for both your health and the peak performance of the machine. We recommend cleaning the juicer immediately after use, since cleaning the machine as quickly as possible is the easiest way to remove food articles.

1. MINERAL SCALES : After using the machine for some time, you may notice a calcium or mineral deposit on the surface of the twin gears.
   This mineral deposits may be removed from the tips of the twin gears by running soaked almonds through the machine. Another excellent way to remove mineral scales is to soak those affected parts in a pure vinegar bath overnight. This loosens the scaling and much of it can be brushed off. This process maybe repeated as necessary. The vinegar used for de-scaling can be stored for reuse. Please label the storage bottle properly so that it is not accidentally used in food preparation.
   
   Tips! To prevent mineral scales, thoroughly clean the twin gears with warm water immediately after juicing. If delays on above cleaning, the mineral deposit starts to build up (It looks like a very thin film on the surface of twin gears).
   
   
2. STICKY RESIDUE : Dried fruits and nuts can be very sticky on the inside surface of the juicer. To remove the residue more easily, run a couple of stalks of celery through the machine before disassemble the machine.
   
   
3. MOTOR BASE UNIT : Wipe the exterior surfaces with a damp cloth and dry with a clean towel. For keeping the best polish, clean the parts with the soft sponge first and dry it with the soft towel. After cleaning the juice extractor, let it dry thoroughly.
   
   It is not recommended that harsh chemical, such as bleach, be used to remove food stains from the juice extractor.

Different between 5500 and 7500
7500 included automatic function.

When you input vegetables (for example wheat grass, etc.) too much for extraction, 7500 senses automatically and vomit out after several times of start and reverse.